FOXEER SP Racing F3 Race Flight Controller

Artikelnummer: FOX-MR1240

Top Flight-Controller für FPV RaceCopter und 3D


CHF 22.90

inkl. 7,7% MWST
zzgl. Versandkosten

UVP: CHF 26.00
(bei RC3D.CH sparst du 11.92%, ≙ CHF 3.10)
nicht an Lager


Der SP Racing F3 Flight-Controller wurde speziell für eine atemberaubende Flying Experience entwickelt . Er liefert alle notwendigen Funktionen für Multicopter (Tricopter bis Octocopter), Flugzeuge, Helikopter und Landgebundene Fahrzeuge. Ob für FPV-Racing, Acrobatic oder auch für Aerial Photographie. Die Konfiguration erfolgt vorzugsweise über "Cleanflight".

Specification:
- Version: Acro 6DOF(Acro version has no Compass and Barometer Sensors)
- Weight: 7.8g
- Size: 36x36mm board, 30.5 mm mounting holes
- STM32F3 CPU,72Mhz inc FPU
- High-capacity Flash
- MPU6050 Accelerometers and Gyroscopes
- MicroUSB socket
- 4 x 4 pin JST-SH Socket (I2C, SWD, 2xuart)
- 2 x 8 pin JST-SH Socket (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
- 8 x 3 pin though-holes for pin headers for ESC/Servo connections
- 2 x 4 pin though-holes for the 2x serial ports
- 2 x 2 pin though-holes for battery voltage and buzzer

Features:
- No compromise I/O
- Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time!
- On-board high-capacity black box flight log recorder optimizes your tuning and see the results of your setup without guesswork.
- Next-generation STM32 F3 processor with hardware floating point unit for efficient flight calculations and faster ARM-Cortex M4 core.
- Stackable design - perfect for integrating with OSDs and power distribution boards.
- 16 PWM I/O lines for ESCs, Servos and legacy receivers. 8 available on standard pin headers. 8 via side mounted connectors.
- Full support for OneShot ESCs for easy PID tuning and a sharper response.
- SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers supported; No external inverters required (built-in).
- Dedicated output for programmable LEDs - great for orientation, racing and night flying.
- Dedicated I2C port for connection of OLED display without needing flight battery.
- Battery monitoring ports for voltage and current.
- Sonar support for precision low-altitude hold.
- Buzzer port for audible warnings and notifications.
- Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.
- Symmetrical design for a super tidy wiring.
- Wire up using pin headers, JST-SH sockets or solder pads. Use either right-angled or straight pin-headers.
- Barometer mounted on the bottom of the board for easy wind isolation.
- Loop times up to ~2x as fast as previous-generation STM32F1 based boards.
- Configuration of the flight controller via a cross-platform GUI (Windows/OSX/Linux).
- A variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more supported

Lieferumfang
SP Racing F3 Flight Controller
Pin Header
Cables

Durchschnittliche Artikelbewertung

Gib die erste Bewertung für diesen Artikel ab und hilf Anderen bei der Kaufenscheidung: